Rates

 

Just about every person will have their private notions when it comes to A Step-by-Step Guide to Installing a Bathtub.

Installing a bathtub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult project. If the old bathtub is readily obtainable, the project can relocate immediately; if you have to open a wall surface to get rid of the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and also embeded in the brand-new one. Make certain you have qualified yourself for the job as well as are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is far better to think about utilizing one before you start. Possibilities are you may need a specialist plumber to make tube connections.
This post will help you mount a new bathtub in your shower room if you have actually currently bought a new bathtub and also do not require to alter the setup of your previous supply of water pipes.
Your devices and also product checklist must make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water system. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be quite bothersome as a result of the restricted accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before going on to fit the new taps, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Fitting New Touches

If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and the sink. Protect the tap in position with the supplier provided backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The previous type ought to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Setting up the Bathtub

Utilizing both wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The next objective is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub till the spirit level checks out level.
To install taps, fit all-time low of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; after that do the very same for the other tap.
Turn on the supply of water and also check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as likewise check the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait until the tub has actually been used at least once as this will settle it right into its last position.

 

 

Preparing for the Installation

Firstly, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final placement.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, triggering the water to permeate the wall surface in between the bath and also the tiling, resulting in problems with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealer can split rather very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant sticky as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you enjoy more info about Installing A Bathtub? Leave feedback directly below. We will be interested to listen to your opinions about this write-up. In hopes that you come back again before long. Loved our write-up? Please share it. Help someone else check it out. Many thanks for your time spent reading it.

Opt for our expert plumbers.